Snapshot store

The swarm's btrfs receive endpoint. Hives push agent snapshots to it over the WireGuard mesh; a destination hive later pulls one back to complete a migration.

Two things it is not, both worth stating because both are easy to assume:

Enabling it

services.hyperhive.snapshotStore = {
  enable = true;
  path = "/var/lib/hyperhive-snapshots";  # must be on btrfs
  port = 51821;
};

# The mesh is a hard requirement, and is asserted:
services.hyperhive.swarm.wireguard = {
  enable = true;
  address = "10.100.0.9/24";
  privateKeyFile = "/etc/wireguard/hive.key";
};

The store host is a swarm member like any other: it gets an entry in services.hyperhive.swarm.hives, the same directory every host holds. See swarm/ for the mesh itself.

Note that the mesh is gated on swarm.wireguard.enable, not on c0re.enable --- a store host runs no hive and would otherwise get no wg-hive interface at all.

Pointing a hive at it

The block above configures the host that receives. Every hive that pushes separately needs to be told where the store is:

services.hyperhive.swarm.snapshotStore = {
  address = "10.100.0.9";  # the store's mesh address, no prefix
  port = 51821;            # optional; must match the receiver's port
};

Two deliberate asymmetries in that pair, both easy to misread as inconsistency:

Note the option lives under swarm.* while the receiving host's lives under services.hyperhive.snapshotStore. That is the distinction the two namespaces carry throughout: swarm.* describes the swarm as seen from this host, and a bare services.hyperhive.<service> describes a role this host performs. A store host sets both --- one to run the receiver, one only if it also runs a hive that pushes.

With it set, hivectl agent <name> subvol snapshot push <label> [--parent <label>] streams a snapshot straight into the store. There is no destination argument, because a swarm has exactly one store (see One subvolume per agent, not per hive), and no credential argument, because the mesh is the authentication.

The mesh is the authentication

There are no certificates here, and no key material of its own. That is deliberate rather than an omission.

WireGuard's cryptokey routing already binds a peer's source address to its public key: the swarm module configures each peer with allowedIPs = [ peer.wireguardAddress ], so a packet arriving from that address provably came from the holder of that private key. A packet that reaches the receiver has therefore already been authenticated by the kernel.

Layering TLS client certs on top would authenticate the same fact a second time, and add a credential with an expiry --- a migration that fails because a renewal quietly didn't happen, discovered on the day you need to move an agent.

One subvolume per agent, not per hive

The destination is keyed by agent.

This is not cosmetic. After a migration, an agent's next incremental send arrives from a different hive than the previous one. Keying by hive would split that agent's snapshot chain across two directories, and btrfs send -p would fail to find its parent --- breaking exactly the case the store exists to serve.

What the sender can and cannot choose

A btrfs send stream carries no notion of which agent it belongs to, and the subvolume name inside it is chosen by the sender. So the protocol is one agent <name> header line, then the raw stream.

The rule that matters:

The receiver owns the destination root. The sender-supplied name is validated, never used as a path.

Validation is a whitelist --- [A-Za-z0-9_-]+ and nothing else. No slash and no dot means neither directory traversal nor an absolute path can survive it. It is deliberately a whitelist and not a list of forbidden characters: a blocklist only ever excludes the attacks somebody already thought of.

Reachability

The receiver is socket-activated, and the socket binds this host's mesh address, never a wildcard. Both the mesh being enabled and the address being set are assertions, not documentation --- bound to 0.0.0.0 this socket is an unauthenticated remote write into agent state.

Binding is not sufficient on its own. NixOS's firewall is default-deny and filters in netfilter, before a packet reaches a bound socket, so the port is opened explicitly --- and scoped to the mesh interface:

networking.firewall.interfaces.wg-hive.allowedTCPPorts = [ cfg.port ];

A host-wide allowedTCPPorts would open the port on every interface including a public NIC, leaving only the socket's bind address between the internet and a root btrfs receive.

Operating it

Confinement is the deployment's job

btrfs receive needs CAP_SYS_ADMIN, so the receiver runs as root. The unit sets ProtectSystem=strict, ProtectHome, PrivateTmp and a narrow ReadWritePaths --- but those are defence in depth, not a boundary: a process holding CAP_SYS_ADMIN can call mount(2) and undo the namespace they set up.

The boundary is the machine. The intended deployments are:

The second is worth keeping deliberately, and not only for convenience: it means the confined path is exercised by every local deployment. The usual failure mode for an isolated variant is that nobody runs it day to day, so it rots and is discovered broken in production.

⚠️ The assumption to keep true over time: the store host runs nothing else. That is true on day one and quietly false the day someone notices the box has spare disk. Nothing in the config objects when it stops being true.

It holds every agent's state from every hive

Which makes it the highest-value target in the swarm by a wide margin, and means it should get the treatment a backup host gets --- restricted access, and a decision (rather than an omission) on encryption at rest.

The trap is the label: this box holds backup-grade data while not being called a backup, so it can end up with backup-grade exposure and non-backup-grade controls. Nobody puts a migration staging area on the access-review list.

What a snapshot contains

The snapshot covers an agent's state subvolume, which is the parent of state/, claude/ and harness/ (see docs/persistence.md's btrfs subvolume section for how and when that subvolume is created). Consequences:

It does not cover the agent's applied config (/applied/<name>/) or its topology entry, both of which live outside the subvolume. A restore therefore yields an agent's memory without its definition; closing that gap is tracked separately.

Retention

Retention lives on the sending side (last-N by count, swept periodically), not here. Count rather than age is deliberate: a count is bounded by construction, whereas an age policy silently scales disk usage with how hot a hive runs.

Per-agent or per-hive btrfs qgroup quotas are not configured yet. Without them one runaway hive can fill the store and take out every other hive's snapshots.

Not built yet

The pull side. Push is safe with minimal authorisation because a hive can only ever write to a chain it owns. Pull is the direction that needs a policy: unrestricted, any compromised hive could read every agent's state from every other hive. It needs a notion of which hive currently owns which agent, and that ownership record lands with the swarm controller work.

With a single hive the question is trivial --- the only peer owns everything it sends --- which is why the receive half ships first.